Home Showroom LCR Meters / Instruments

Product ID: LCR 200

200 KHz LCR Meter W / RS - 232 Interface ( LCR 200)

Specifications:

• Test condition
  • Frequency: 100Hz / 120Hz / 1KHz / 10KHz / 100KHz / 200KHz.
  • Level: 1V rms / 250mVrms / 50mVrms / 1Vdc (DCR only).
  • Measurement parameters: Z, LS, LP, CS, CP, DCR, ESR, D, Q, and Dia.
  • Basic accuracy: 0.1%.
• Primary parameters display
  • Z: AC impedance.
  • DCR: DC resistance.
  • LS: Serial inductance.
  • LP: Parallel inductance.
  • CS: Serial capacitance.
  • CP: Parallel capacitance.
• Secondary parameters display
  • Dia.: Angle impedance.
  • ESR: Equivalent series resistance.
  • D: Dissipation factor.
  • Q: Quality factor.
• Combinations of display
  • Serial mode: Z-Dia., CS-D, CS-Q, CS-ESR, LS-D, LS-Q, LS-ESR.
  • Parallel mode: Cp-D, Cp-Q, LP-D, LP-Q.
• Measurement range
  • Z: 0.000 Ohm to 500.0 Ohm.
  • L: 0.030 uH to 9999 H.
  • C: 0.003 uH to 9999 H.
  • DCR: 0.000 Ohm to 500.0 M Ohm.
  • ESR: 0.000 Ohm to 9999 Ohm.
  • D: 0.000 to 9999.
  • Q: 0.000 to 9999.
  • Dia.: -180.0 degree to 180 degree.
  • V: 0.000mV to +/- 600.0V.
  • ESR: 0.000 Ohm to 9999 Ohm.
  • D: 0.000 to 9999.
  • Q: 0.000 to 9999.
  • Dia.: -180.0 degree to 180 degree.
  • V: 0.000mV to +/- 600.0V.
  • I: 0.000mA to +/- 2.000A.
• DC voltage measurement
  • Range: 2V, 20V, 200V and 600V.
  • Resolution: 1mV, 10mV, 100mV, 1V.
  • Accuracy: +/- (0.4% + 3 digits).
  • Input impedance: 1M Ohm.
• AC current measurement
  • Range: 2A, 0.2A, 20mA and 2mA.
  • Resolution: 1mA, 10mA, 100mA, 1A.
  • Accuracy: +/- (0.8% + 5 digits) @ 40 Hz ~ 1 kHz.
  • Input: Impedance 1M ohm.
• AC current measurement (true RMS)
  • Range: 2A, 0.2A, 20mA and 2mA.
  • Resolution: 1mA, 10mA, 100mA, 1A.
  • Accuracy: +/- (0.8% + 5 digits) @ 40 Hz ~ 1 kHz.
  • Current Shunt: 0.1 Ohm @ current > 20mA / 10 Ohm @ current
  • Continuity check
    • Continuity thresh hold: 50 Ohm (approximately).
    • Continuity indicator: tone buzzer.
    • Input protection: 600 Ohm (max).
  • Diode test measurement
    • Test current: 2.5mA (typical).
    • Open circuit voltage: 5.0V DC (nominal).
    • Input protection: 600V (max).
  • Diode test measurement
    • Power source: AC 110 / 220V +/- 10%; 50 / 60 Hz.
    • Operating temp: 0 to 40 deg C (operating); < 85 % RH.
    • Storage temp: -20 deg to 70 deg C.
  • Genearl
    • Dimensions: 300 mm x 220 mm x 150 mm (11.8 inch x 8.7 inch x 5.9 inch) (D x W x H).
    • Weight: 4.5 kg.
    • Standard accessories:
      • TL09C kelvin clips x 1 pc
      • Test leads x 1 pc; power cord x 1; instruction manaul x 1.
    • Optional accessories:
      • TL09A SMD test probe.
      • TL 09B component fixture.

Features:

• Measurement parameters: Z, LS, LP, CS, CP, DCR, ESR, D, Q, and Dia.
• Test conditions: 100MHz, 120Hz, 1KHz, 10KHz, 100KHz, 200KHz basic accuracy 0.1%; test voltage: 1Vrms, 250mVrms, 50mVrms, 1Vdc (DCR only).
• DMM functionalities.
• Dual LCD display with LED backlit.
• Open / short calibration.
• Remote binning capacity.
• Auto range / range hold selection.
• RS-232 interface.

Contact Detail

Address:4F-1, No. 225, Sec. 3, He-Ping East Road Taipei, 110 Taiwan
TEL:886-2-27375866
FAX:886-2-27373343
Email:sales@tecpel.com ; tecpel@seed.net.tw
URL:http://www.tecpel.com http://www.oka.com.tw